中文版 ENGLISH
服务支持
常见问题您的当前位置:首页 >> 常见问题
电视机软件如何升级?
作者:service zhu 发布时间:2014年3月31日
 

问:电视机软件如何升级?

主板采用FLASH ROM存储程序可以反复擦写可预先烧录软件到FLASH IC再装入主板相应位置也可通过VGA串口USB端口进行升级软件。程序与主板的功能有关不同功能的或不同方案的主板应烧入不同版本的程序。一般来讲,通过USB端口直接升级的方法是最为简单与快捷的。

MSTAR主板方案6M1816M18218VG为例,其升级步骤以及升级注意事项,见如下:

电视机通过USB端口直接升级的方法:

1,将新软件拷贝到一USB盘内,再把U盘插到电视机的USB端口上;

2然后,请通电使电视机亮着红灯”(备注:只需让电视机通上电,但不要开机启动的)大约2钟左右的时间你应发现该指示灯会自动进入慢慢的闪烁状态,大约几十秒钟之后,指示灯从慢慢闪烁状态转为"快闪"状态,最后停止闪烁转入红色指示灯状态(表示升级已完成,可以拔掉USB盘了)。

3关掉电视机电源,再开机,升级操作完毕

请注意:

当指示灯处在闪烁状态时,表示已进入升级过程中,此时,千万不可断电;

当指示灯从慢慢闪烁状态转为"快闪"状态时,表示升级过程很快完毕,需请再等片刻,直到指示灯停止闪烁为止。

用于升级的U的质量必须是好的也不能有病毒文件或者有其它文件在内

如果新软件bin文件放在RAR压缩包里面,那么,必须先把对应的软件bin文件从其压塑包里面解压出来之后,再把那个新软件bin文件直接考到U盘中;

软件Bin文件的名称不可变更,否则,升级无法进行!

以下英文版,可供海外客户参考:

This manual will introduce 2 upgrading methods select one option

option 1User menu Upgrading

Please copy the new software to the USB;

Power ON the TV , and then link the USB to the USB port.

Press MENU to display the main menu. then press    /    to the OPTION menu. and

then select the software in the root of your USB memory;

Press ENTER .then press    to update.

After finishing the above steps, the screen will be black, then the indicator will be turned to

red color, that all the operation is finished

option 2Power On upgrading

Please copy the new software to the USBlink it to the USB port of TV,

Re-power on, if the LED blinks continually, it means the upgrading is on process,

while the LED light off means the upgrading has been completed.

Remarks

1Do not OFF the power during the upgrading.

2The USB devices should be without computer virus or other files inside;

3If the new software is put in a RAR package, you must be decompress the software package from the RAR package.

4The new software name below (Do not be change it):

bin_6m181.binbin_6m182.binbin_6m182_VG.bin;,,,

5When upgrading, LED blink slowly every 1 second.

Upgrade success, LED blink quickly every 1/4 second.

Upgrade fail, red LED lights long time and green LED lights short time in cycle

6After upgrading the software. You had better enter the default menu to resume as follows:

press the remote,enter the pass word “MENU1147”, now the TV will display with ““Factory Setting” .

---Select the option “INIT TV”, and then press      on the remote to reset it.

问:SIS221SIS231主板方案如何升级?

This manual will introduce 2 upgrading methods select one option

option 1:Upgrade on power supplying

a)    Make sure the main board be in no power supply situation.

b)    Put USB key to main board USB terminal.(USB key has the upgrade bin file)

c)    Power supply to main board, then LED on IR receiver should be blinking slowly.

d)    Wait LED on IR receiver blinks quickly, which means upgrade is finish.

e)    Disconnect the power supply. Done!

Remarks

1Do not OFF the power during the upgrading.

2The USB devices should be without computer virus or other files inside;

3If the new software is put in a RAR package, you must be decompress the software package from the RAR package.

4The bin file (new software name) : SISEU23X8M.bin (Do not be change it)

5When upgradingLED blink slowly every 1 second.

Upgrade successLED blink quickly every 1/4 second.

Upgrade failred LED lights long time and green LED lights short time in cycle

6Because the initial time of some USB keys are longer, main board cannot detect the USB key when power supplying. If so, please upgrade the main board in factory menu.

option 2 :  Upgrade in factory menu

a)    Power on TV set.

b)    Put USB key to main board USB terminal.(USB key has the upgrade bin file)

c)    Press remote control key -> Menu1147. Enter factory menu.

d)    Select Update -> USB Update -> USB Update Start.

P.S  Factory menu upgrade OSD indication

Start upgrading, following OSD will pop-up

System auto loads the upgrade bin file and start upgrading. Processing bar will be shown and LED on IR receiver will blink.

When upgrade is finishfollowing OSD will be shown. Then power down the TV and power up again.

Remarks

1Do not OFF the power during the upgrading.

2The USB devices should be without computer virus or other files inside;

3If the new software is put in a RAR package, you must be decompress the software package from the RAR package.

4The bin file (new software name) : SISEU23X8M.bin (Do not be change it)

5When upgradingLED blink slowly every 1 second.

Upgrade successLED blink quickly every 1/4 second.

Upgrade failred LED lights long time and green LED lights short time in cycle

问:MSD309主板方案如何升级?

This manual will introduce 2 upgrading methods select one option

option 1 : User menu Upgrading

Copy the bin file (Software) to a USB disk. and then link it to the USB proof the TV.

Search for the SETUP and select Software Update by L/R remote control key on User OSD Menu.the pictures below are the upgrading procedure for your reference

  

option 2Power On upgrading

Please copy the new software to the USBlink it to the USB port of TV,

Re-power on, if the LED blinks continually, it means the upgrading is on process,

while the LED light off means the upgrading has been completed.

Remarks

1Do not OFF the power during the upgrading.

2The USB devices should be without computer virus or other files inside;

3If the new software is put in a RAR package, you must be decompress the software package from the RAR package.

4The new software name below (Do not be change it):

5When upgrading, LED blink slowly every 1 second.

Upgrade success, LED blink quickly every 1/4 second.

Upgrade fail, red LED lights long time and green LED lights short time in cycle

上一篇: 更换屏或主板等主要部件时,应该注意哪些方面的内容?
下一篇: 如何保养遥控器?
关于彩迅| 法律声明| 社会招聘| 网站地图| 友情链接| 联系我们
地址:深圳市横岗镇西坑村宝桐南路88号彩迅工业园
电话:0755-89739888 传真:0755-89739666 邮箱:sales@expressluck.com
版权所有 © 2013 彩迅工业(深圳)有限公司 粤ICP备10214925号 技术支持:新派网络公司